Teledyne-Lecroy 760Zi

Price : Call
  •  Equipment Location : USA
Teledyne-Lecroy 760Zi Opts: WPZi-JTA2

Option: WPZi-JTA2


(From Used-Line T&M Specifications )
Bandwidth  6.0 GHz 
Channels  4  
Sample Rate  40.00 GSa/sec 
Memory Depth  Standard Memory (4 Ch / 2 Ch / 1Ch) : 20 M / 40 M / 40M; Options up to 256 M  
Status -
See also WavePro 715Zi-A, WavePro 725Zi-A, WavePro 735Zi-A, WavePro 740Zi-A

The WavePro 760Zi-A: 6 GHz, 20 GS/s, 4 ch, 20 Mpts/Ch DSO with 15.4" WXGA Color Display. 50 ohm and 1 Mohm Input. 40 GS/s and 40 Mpts/Ch in interleaved mode.

Combining signal fidelity with an architecture that maximizes speed in every performance aspect, the new WavePro 7 Zi-A Series presents a totally new oscilloscope experience from 1.5 to 6 GHz bandwidths. Experience 50 ohm and 1 Mohm inputs for every channel and four inputs into high-speed front end amplifiers and analog to digital converters. Experience the new X-Stream II architecture that provides 10 to 20 times faster long memory performance than any other oscilloscope. Combined with the flexible and deep LeCroy analysis toolbox, the WavePro 7 Zi-A Series gives an unforgettable experience for the debugging, validation, analysis and compliance testing of electronic designs.

  • Freedom from limitations: WavePro 7 Zi-A excels in the way it offers general purpose utility never before seen in oscilloscopes from 1.5 to 6 GHz. All WavePro 7 Zi-A oscilloscopes contain selectable 50 ohm and 1 Mohm input capability. The 4 and 6 GHz models include both ProBus and ProLink input types, which means eight probes can be attached and then multiplexed from the front panel or by remote control. The result— it is easy to hook up a passive probe even on 4 or 6 GHz models—no more frustration and hassle of trying to find a 1 Mohm input adapter.
  • More triggers isolate more problems more effectively: A powerful combination of high bandwidth Edge and ten different SMART triggers allow you to isolate the problem quickly and begin to focus on the cause. Most SMART triggers allow triggering on pulse widths or features as small as 200 ps. A high-speed serial trigger enables triggering on up to 2.7 Gb/s serial patterns of up to 80-bits in length. Built-in hardware clock recovery is also included.
  • TriggerScan™: TriggerScan uses high-speed hardware triggering capability with persistence displays to capture only the signals of interest and provide answers up to 100X faster that other methods.
  • WaveScan™ advanced search and analysis finds problems that triggers will not find: WaveScan provides the ability to locate unusual events in a single capture or "scan" for an event in many acquisitions over a long period of time. Select from more than 20 search modes.
  • Fully integrated mixed signal oscilloscope (4 + 36) option; Jitter and timing analysis package; Spectrum analyzer analysis package; Digital filter software package
  • LeCroy has found a way to make long acquisition memory seamless and pain free to use. The WavePro 7 Zi Series proprietary X-Stream II architecture supports capturing, zooming, measuring and analyzing multiple waveforms at 256 Mpts deep
  • Instantaneous responsiveness: Acquiring and manipulating the longest record lengths and the most complex WaveShape Analysis are all easily handled at the same time
  • X-Stream II architecture: Optimized for fast throughput; Optimized for long memory; Optimized for responsiveness

WavePro 760Zi-A specifications:

  • Vertical
    • Analog bandwidth (maximum): 6 GHz
    • Rise time (10 - 90%): 70 ps typical, flatness mode
    • Input channels: 4
    • Bandwidth limiters: 20 MHz, 200 MHz, 1 GHz, 3 GHz, 4 GHz
    • Input impedance: 50 ohms ±2% or 1 Mohm || 16 pF, 10 Mohm || 11 pF with supplied probe
    • Input coupling: ProLink Inputs - 50 ohms: DC, GND; ProBus Inputs - 1 Mohm: AC, DC, GND; 50 ohm: DC, GND
    • Maximum input voltage: 50 ohms (ProBus): ±5 Vrms; 50 ohms (ProLink): ±4 Vpeak; 1 Mohm (Probus): 250 V maximum (peak AC: <10 kHz + DC)
    • Vertical resolution: 8 bits; up to 11 bits with enhanced resolution (ERES)
  • Horizontal
    • Timebases: Internal timebase common to four input channels; an external clock may be applied at the auxiliary input
    • Time/division range: Real Time - 20 ps/div-2000 s/div; RIS mode - 20 ps/div - 10 ns/div; Roll mode - up to 2000 s/div (roll mode is user selectable at >=100 ms/div and <=5 MS/s)
    • Jitter noise floor: 560 fs (TIE, typical)
    • Trigger and interpolator jitter: 1 psrms, typical; <0.1 psrms, typical (software assisted)
    • Channel-channel deskew range: ±9 x time/div setting, 100 ms max, each channel
    • External Timebase Reference (Input): 10 MHz; 50 ohms impedance, applied at the rear input
    • External Timebase Reference (Output): 10 MHz; 50 ohms impedance, output at the rear
    • External Clock: 30 MHz-2 GHz, 50 ohms impedance, applied at the auxiliary input
  • Acquisition
    • Sample rate: 40 GS/s on two channels; 20 GS/s on four channels
    • Single-shot sample rate/ch: 40 GS/s on 2 Ch; 20 GS/s on 4 Ch
    • Random Interleaved Sampling (RIS): 200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
    • Maximum Trigger Rate: 1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
    • Intersegment Time: 1 µs
    • Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments): 20 M / 40 M / 40M (4500)
    • Memory Options (4 Ch / 2 Ch / 1Ch): S-32 Option: 32M / 64M / 64M (15,000); M-64 Option: 64M / 128M / 128M (15,000); L-128 Option: 128M / 256M / 256M (15,000)
  • Triggering
    • Modes: Normal, Auto, Single, Stop
    • Basic triggers: Edge, Window, TV-Composite Video
    • SMART triggers: State or Edge Qualified, Qualified First, Dropout, Pattern
    • Sources: Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
    • Coupling Mode: DC, AC, HFRej, LFRej
    • Pre-trigger Delay: 0-100% of memory size (adjustable in 1% increments of 100 ns)
    • Post-trigger Delay: 0-10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
    • Hold-off by Time or Events: From 2 ns up to 20 s or from 1 to 99,999,999 events
    • Internal Trigger Range: ±4.1 div from center
    • External Trigger Input Range: Aux (±0.4 V); Aux/10 (±4 V)
    • Max Trigger Frequency, SMART Trigger: 2.0 GHz @ >= 10 mV/div (minimum triggerable width 200 ps)
  • Interface
    • Remote control: Via Windows Automation, or via LeCroy Remote Command Set
    • Network Communication Standard: VXI-11 or VICP, LXI Class C (v 1.2) Compliant
    • GPIB Port (optional): Supports IEEE - 488.2
    • LSIB Port (optional): Supports PCIe Gen1 x4 protocol with LeCroy supplied API
    • Ethernet Port: Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
    • USB Ports: Minimum six total (including three front panel), USB 2.0 ports support Windows compatible devices
    • External monitor port
    • Peripheral bus: LeCroy LBUS standard


To:  Liberty Test Equipment, Inc.
All fields are required
 Remember me
 Send me a copy.
News, sales, & auction announcements
About the Seller
since 2006

Liberty Test Equipment, Inc.

Visitors viewed Liberty Test Equipment, Inc. ads in the last 30 Days.

The dealer's latest update: over 30 days

1640 Lead Hill Blvd. Suite 120 Roseville 95661 CA USA  
More about this seller »

Sales Conditions:

END USERS ONLY! 10-day right of return, 12-month warranty, around-the-clock NIST traceable/ISO registered lab & all standard accessories. Pricing and availability are subject to change. Many payment options, terms, credit card, checks, lease terms, rental, etc.

Some of the services we offer:

(Rentals) (Calibration) (Repair) (Manuals) (Market place)